Accessories

COMPONENTS Accessories and components giving you chance to improve your enclosures abilities.

Subcategories

Knurled Plastic-Head Thumb Screws

Altınkaya Enclosures manufactures also knurled plastic-headed screws which are a sort of washer-faced knurled thumb screws with a slotted drive in the screws head from our broad variety of thumbscrews. The plastic thumb screw's head is designed to make spinning with one hand easier.

They're a great choice for assemblies with often changing components, such as access panels. Because of the manual action, knurled thumbscrews are essential and can be utilized in a variety of industrial applications, heavy-duty enclosures, instrument enclosures. Thread sizes M4, M5, M6, and M8 are available.

Multi Hole Seals for Cable Glands

Multihole Seals

In instances where more than one non-terminated cable or wire must be placed into the same cutout, use a multiple-hole seal. After removing the original internal rubber seal, use the seals below with standard industrial domed glands by ITC (nylon or metal, brass).

For cable gland applications and IP rated applications, multihole seals are available. The cable glands and multihole seals are available separately.

Screws

SCREWS Screws for mounting PCB cards etc in your enclosure.

Cable Grommets

Sharp edges, continual mechanical stress, chemicals, or environmental impacts are just a few of the reasons that might cause cable damage. Cable grommets reduce these dangers while also protecting the cabling.

Snap-in cable grommets, for example, assist reduce abrasion when cables must be routed through small round holes. The use of so-called grommet strips is a viable solution for bigger or unshaped cut-outs with sharp or straight corners.

Cable grommets that are placed into cable ends are another type of cable grommet. Cables are relieved of pressure by these grommets. Other cable entrance sleeves, known as anti-kink grommets, protect the cable from bending or kinking. Some cable grommets even integrate strain relief and bend prevention in one.

Self-Clinching Fasteners

Self Clinching Fasteners

Self-Clinching fasteners are mechanically pushed threaded nuts, studs, or blind and thru-hole standoffs into sheet metal to give firm attachment points. Self-clinching fasteners are a highly helpful item in the assembly of devices and electronics in universal electronic and electrical enclosures, as they solve a number of component mounting problems.

Under one roof, Altınkaya Enclosures can overcome this problem. This is something we can do with our metal and aluminum instrument enclosures.

Studs

Nuts

Blind Stand-offs

Thru-Hole Stand offs

Brass Inserts

Threaded brass inserts manufactured of high-quality brass. The mechanical features of brass threaded inserts are excellent: corrosion resistance, efficient machinability, and strong electrical conductivity. They are often less expensive than steel(s) and are well suited to thermoplastic, thermoset, and composite material assemblies.

Screws-

Cable Glands

Cable glands are cable entry devices designed to attach and secure the end of a cable to the enclosure. We have brass and plastic cable glands and plastic blind stops in our store.

Handles

Since we have access to a wide variety of handles, our clients' preferred options are the small chrome, medium chrome, and large plastic handles shown below.

Rackmount enclosures, instrument enclosures, heavy-duty aluminum enclosures, laboratory enclosures, and any other miscellaneous application that requires them typically utilize handles.

When choosing the handle, the axial distance must be taken into consideration.

Battery Holders

BATTERY HOLDERS If you need a power source in your project we offer you different types of battery holders for all size of batteries. Also you can find PCB solderable holders or battery contacts and external battery holders in our list.

Button Caps

BUTTON CAPS Colored, different shaped and different sized button caps for your control panels.

Card Rails

CARD RAILS Card rails to mount your PCB to the enclosure without using screws on board. Card rails can be used both horizontal or vertical.

Terminals

TERMINALS Terminal accessories for different types of enclosures.

Standoffs

Brass standoffs, both male and female types, are used within electronic enclosures to raise components above the enclosure surface. These brass standoffs parts are giving the ability to fasten sensitive projects to keep safely inside of electronic boxes.

Captive fasteners are an essential component that supports in the mounting and housing of inserted circuit board components within electronic enclosures and boxes. Standard standoffs, plastic spacers, self tapping standoffs, and pcb support pillars are the four types of fasteners available. These versions are ideal for a variety of applications.

The objective of handling Plastic Standoff accessories is to avoid short circuiting and ruining electrical components. The use of stand off between printed circuit board (PCB) electronic components and the enclosure case body is described above. Plastic material products are recommended to retain a minimal distance between the board and the enclosure wall. This material divider may be used in a variety of applications with electronic boxes. Male-female standoffs and female-female stand offs are the two typical forms of fasteners and fixings mechanical components.

Enclosure Feet

Rubber feet protect benchtops, provide friction to avoid slipping, dampen sound, and improve the overall appearance of your enclosure. We have versions that fit in industrial environments, as well as housings and electrical boxes for desktop computers. Consider the size, weight, and interior space while making your decision. Some rubber foot variants have a metal washer that protects the enclosure feet while screwing them in place. Check to see if the rubber feet models are push-in or screw-in.

Tilt feet -which Altınkaya manufactures in-house -also have a selection of tilt foot bars for small plastic enclosures, instrument enclosures, heavy-duty housings, and laboratory cases that can be installed anywhere on the base and provide an ergonomic viewing posture.

Check the product file for detailed information for highness, screw hole, and thickness. Detailed information is provided by our Altınkaya Enclosures sales team.

Knobs

Control knobs for rotary switches, rotary encoders, and shafts are known as rotary switch knobs. By altering levels, they play a crucial function in making a gadget easier to control. The intended input is determined by the degree of rotation applied to the switch knob.

Miscellaneous Accessories

Led Light Pipes

LED light pipes are optical connectors that transport light from a board-mounted LED to the location where it is needed. They allow you to modify the position of your LED light without changing the location of the LED itself, giving you more light distribution versatility. The majority of LED light pipes are panel mounted or press fit, making installation simple.

An LED must be properly matched to a light pipe in order to capture the maximum amount of light. The proper LED light pipes for your project will be determined by lens size and mounting requirements, as well as choosing between LED styles. At Altınkaya Enclosures, we manufacture led light pipes.

Enclosure mounting kits

Wall Mounting Kits For your enclosure, you'll need flange kits, mounting kits, and surface mounting brackets. Mounting kits attach to the enclosure's base and offer a stable mounting location for your box. Aluminum, steel, ABS, and PC plastic mounting kits are offered.

Pole Mounting Kits are offered for your IP67 hinged plastic cases. The pole mounting brackets enable a stable mounting option on poles. Mast mounting brackets are available in different sizes.

DIN rail makes it simple to install and replace terminal blocks and other devices. DIN rails are manufactured of steel or aluminum and come in a variety of lengths that meet international requirements. DIN rail brackets, whether straight or angled, tilt and/or raise rails for easy wiring. For easy installation on 35mm DIN rails, small electronics are connected to mounting clips. There are plastic and steel DIN rail brackets for the devices and electronics to mount on DIN rails.

Panel Mounting fixing clamps are used from the back of the control panel, the screw clamp is put on the enclosure. The enclosure would then be firmly pushed against the control panel's wall using the included screw.

Latches and Hinges

Draw latches from Altınkaya Enclosures for Electronics provide a wide choice of options for securely joining panels, plastic cases, and enclosures for electronics. Altınkaya draw latches offer a mechanical benefit by allowing hand efforts to generate the forces required to compress gaskets, seal enclosures, and prevent rattle. They are available in a variety of dimensions including over-center, adjustable, and heavy-duty.

Plastic hinges for enclosures allow doors to open and close by attaching them to buildings or surfaces. When the electronics cases do not have a hinge option, Altınkaya plastic hinges can be used to attach random enclosures, covers, and bodies. There will be screw holes when drilling a hole to mount the hinge on the enclosure body and lid, but plastic enclosure hinges have a seal option that allows them to be put on IP67 enclosures as well and the enclosure can keep the IP67 rating.

RF shields

RF SHIELDS RF shields block radio frequency electromagnetic radiation and by this way help protecting your device. We have different sizes of RF shields, select one of them or ask us to produce your custom size.

Mounting Plates

Sort by:

View

There are 305 products.

A-310

ABS Plastic Ventilation Apparatus

€0.88

Filter by

Categories

Accessories